The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need. For employ with 5/8” shaft sizes. Includes set screws. Further Features: Made of Steel For use with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering on hand requirements and allowing for changes in shaft size if necessary. The barrel of the split tapered bushing is definitely split in two locations and is normally keyed to the shaft. The barrel OD is also keyed to the travel component aswell. The advantage of the split tapered bushing is it will hold, whether or not the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are trusted together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made from high quality engineered components with great tolerance. The feature is easy to use and needs no additional alteration. These bushings can match almost a myriad of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations add bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: full range of both metric and imperial offered.
Standard range fits up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete brief reach range obtainable, for compact lightweight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for toughness and strength. U1 bushings are being used in an extensively wide selection of applications, which include; sprockets, Split Taper Bushing china shaves, pulleys, gears, and much more, we also offer all of these items. What models this bushing apart may be the high-quality steel structure along with exact manufacturing and high quality control; this ensures that you always get a premium quality regular product. What really units us apart from the other men is our experienced expert workers and our company-wide objective of customer satisfaction.
1. Be certain the tapered cone areas of the bushing and the inside of the driven merchandise happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or different component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding in shape on shaft.
4. With essential on shaft, slide the sprocket or other component type to the desired position on the shaft. Make sure to leave the heads of the cap screws accessible.
5. Align the sprocket or component type, tighten the screws alternatively and progressively until they will be pulled up tight. Do not make use of extensions on the wrench handles , nor permit the sprocket or component to become drawn i connection with flange of bushing. At this stage there should be a gap between your bushing flange and sprocket, make sure this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for positive drive and greater torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep up concentric bores
Available in in ., metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Double Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys on both the shaft and product to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need. For apply with 5/8” shaft sizes. Includes set screws. Extra Features: Manufactured from Steel For make use of with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, ideally lowering on hand requirements and enabling improvements in shaft size if important. The barrel of the split tapered bushing is definitely split in two spots and is definitely keyed to the shaft. The barrel OD is also keyed to the travel component aswell. The good thing about the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings happen to be interchangeable between manufacturers.