The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software enables simple interactive product selection of the complete gearbox and gear-motor system. Cat4CAD supports you in choosing and configuring the products, provides you the chance to print out extensive technical data linens, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Essential gear motors, ” or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft mounting, inch and metric result shafts, mounting pilots and flanges offer a wide selection of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for globally multi volt/Hz requirements plus modular design to accept brakes, encoders or pressured cooling.
High efficiency engine design available
Innovative self-locking, self-aligning taper shaft electric motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals upon heat treated, plunge helical bevel gear reducer ground shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It is offered as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors can be found in three stage high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and output shaft options. Additionally, you will see fixed and variable quickness motors and range of ratios available in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Essential dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying needs of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological articles of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully used in a multitude of commercial and civil applications. They are B-Series units that offer excellent affordability and result torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with compact motor, PB-fitted for motor coupling with flexible joint
Casing with ft FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and result flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced output, assemble/disassemble kit
Series EP right position helical bevel equipment motors offer ratios from 8:1 to 160:1 in three stages or up to 10000:1 in five phases. Motors can be found up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and may be offered with single or double extended output shafts.
Units are also available because shaft mounted or with result flanges and are available for mounting horizontally or vertically. The units can also be offered with a bolt on torque response bracket and all variants are available possibly motorised or with an insight shaft assembly.
Adding to the brand new range of Ever-Power helical equipment motors the product takes benefit of our a long time of accumulated design expertise together with the use of high quality materials and elements. The outcome is a series of speed reducing geared motors providing high load transporting capacities, increased efficiency, quiet running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double oil seals, on input and output shaft as required.
All systems are dimensionally interchangeable with additional major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Products can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemical substances, pharma, packaging, food processing, plastic material and automation etc.
Key Features:
Sizes: A40-A50-A70
Available versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with small motor
Cases with feet, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Excellent mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, great appearance ,and solid capacity of being overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to since high because 96% with low energy consumption, strong adaptability and is capable of operating continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal device, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.