Product Description

Casing Oscillator KRT150

 

1. Description

Greater embedding pressure can be achieved by Casing oscillator instead of Casing Drive Adapter, Casing can be embedded even in hard layer.
Casing oscillator owns such merits as strong adaptability to geology, high quality of completed pile, low noise, no mud contamination, slight influence to former foundation, easy control, low cost, etc. It owns advantages in following geological conditions: instable layer, underground slip layer, underground river, rock formation, old pile, erratic boulder, quicksand, foundation of emergency and temporary building.
It is especially suitable for coast, beach, old city wasteland, desert, mountain area and the place surrounded by buildings.
 

2. Specifications

KRT150 Casing Oscillator Technical Specification
Casing diameter mm 600/800/1000/1200/1500
Max. Operating pressure Mpa 28
Max.torque KN.m 1500
Rotation angle o ±10o
Stroke mm 450
Max. lifting force KN 2050
Height of Mainframe mm 650
Overall weight Kg 19000
Mainframe pressure KN 1050
Balance weight pressure KN 900
Clamping force(clamp) KN 2200
Clamping force(sub clamp) KN 280
Width of connection box mm 560
Width of tail mm 1600
Width of base frame mm 2720
Overall length mm 4285
Height of tail mm 1170
Height of connection box mm 580
Connection box pin shaft stroke mm 60
Height of jaw mm 630
Height of mechanical fixture mm 1150
Overall Height mm 1780

 

3.Competitive Advantage

(1) Low purchase and transport costs for the shared utilization of rig pump instead of special pump truck.

(2) Low operation cost for the sharing of output power of rotary drilling rig, energy saving and environmental friendly.

(3) Ultra-large pull/push force up to 210t is supplied by lifting cylinder and the large can be achieved with added counter-weight to speed up construction.

(4) Dismountable counterweight from 4 to 10t as required.

(5) Reduction in transport cost for the counterweight is made of cast-in-place concrete.

(6) Work stably-combined action of counterweight frame and ground anchor fix the bottom of oscillator to the ground firmly and reduce the reaction torque generated by oscillator to rig.

(7) High working efficiency for the automatic casing oscillation after 3-5m casing-in.

(8) The distance between oscillator and rig can be adjusted conveniently due to bolt connections.

(9) Added anti-torsion pin of clamping collar to ensure 100% torque transfer to casing.

(10) 0.6-1.5m casing diameter with different clamping collar to meet customers’ needs.

 

4. Using Conditions

1.When the strata conditions are unstable, Casing is required to be driven to overall depth to prevent hole’s collapse. It is called All Casing method (Benoto Method, Shaft Drilling).
2.To drive the Casing and retract it after concreting, Casing Oscillator is strongly recommended to use.
3.With its superior oscillating torque and lifting force, the machine shows the best performance of driving and retracting the casing.
4.If it is used together with Hammer Grab, it shows the fast excavating speed with its big volume of jaw and it is available for excavating gravels and boulders layer.

5. Construction Photos

6.Packing & Shipping

7.Our advantages 

8.Exhibition

9.Certificate

10.FAQ
Q: Why choose us?
  We are professional factory with full export experience. We make sure all qualified goods with high quality reach
international standard
  As experienced exporter, we can give professional advice in transportation method to reduce your cost.
Q: How can I know the production condition?
  After receiving down payment, financial confirmation payment letter will be given to you. If necessary, you will receive videos and photos from production department, quality department and package.
Q: Can I print own logo on package?
   Sure. Customized package and OEM printing are available.
If you have other questions, welcome to contact us!
 

Warranty: 6 Months
Type: Drill
Pressure Pile Driver Type: Hydraulic Pile Driver
Power Source: Diesel
Noise: Without Noise
Certification: CE, ISO 9001:2000
Customization:
Available

|

Customized Request

Shaft Collar

Types of Shaft Collars

A shaft collar is a simple machine component that is an integral part of many power transmission applications. It is most commonly found in motors and gearboxes and serves as a mechanical stop, locating component, and bearing face. Its easy installation and quick assembly make it an ideal component for a variety of applications.

Clamp-style shaft collars

Clamp-style shaft collars are fasteners that fit over shafts. They can be made of aluminum, steel, or titanium. Stainless steel collars are available in corrosion-resistant finishes to prevent galling. Engineered plastics are also available. Black oxide finishes improve corrosion resistance and provide a smooth surface for screw installation.
The holding power of Clamp-style shaft collars depends on the shaft’s bore size and concentricity, which are important factors in many applications. The fastening hardware is also important, as it can affect torque transmission. For example, forged screws are superior to broached screws in a number of ways, including reduced risk of reaming out. In addition, the material of the collar must be strong enough to withstand the torque required by the screw.
Shaft collars are complicated components. Their performance can determine the efficiency of an application. The design process is complex, and many factors are considered. Considerations include shaft geometry, bore size, and style. Shaft collar manufacturers will provide performance information on their website. If you are not satisfied with the information provided, you can contact the manufacturer.
Clamp-style shaft collars are made from high-quality materials. The metal used to produce them is lead-free and stainless, which resist corrosion. Moreover, these shaft collars have a high holding power, so they won’t mar your shaft and ensure proper alignment. These collars can be found in a variety of bore sizes, from 1/8″ to six inches.
Clamp-style shaft collars are available in lead-free steel, 303 and 316 stainless steel, and aluminum. They are available in a one-piece clamp or a two-piece clamp style. They are made of high-grade steel and are machined to a burr-free surface.
Clamp-style shaft collars have two-piece clamps that can be easily disassembled and installed in their proper position. Two-piece clamps are stronger than one-piece collars because all of the clamping force goes directly into the clamping shaft. Two-screw clamps have two and four-screws, and can also be wrench-tightened.
Set screw collars were one of the first shaft collars to be mass-produced. They were often used on line shafting in early manufacturing mills. While they can work well for simple shaft positioning, they’re not the most reliable option for complicated applications. Furthermore, set screws can cause damage to the shaft, making it difficult to reposition the collar or adjust its angle. For this reason, small flats are usually added to the shaft at set screw locations.
Shaft Collar

Set-screw shaft collars

Set-screw shaft collars are used to secure a shaft to a screw. They are available in several sizes and materials. Typical types include the solid, quick-release, split, and threaded styles. They come in an assortment of sizes and materials, including aluminum, zinc plated steel, and black oxide steel. Most are available in stock and are available in various sizes.
These collars come in many sizes and are ideal for use with standard round shafts. They are easy to install and disassemble and feature a high clamping power. They are also available in custom designs and materials. Set-screw shaft collars are available for use in various industries.
The company manufactures a variety of collars, including steel, zinc plated steel, and stainless steel. They also offer custom and adjustable collars. These collars are used in a variety of industries, including the food, chemical, pulp and paper, and wood industries. They are available with a variety of screw threads.
The screw and shaft material relationship must be compatible to ensure a secure fit. In addition, the shaft material should be softer than the screw material. For this reason, set-screw shaft collars are most effective when the shaft is made from softer material. Some setscrew shaft collars feature forged socket set screws to increase their holding power and torque capacity. Additionally, forged stainless steel set screws also increase their performance and hardness.
Shaft collars can be used on machines and transmission applications. They can be adjusted with a set screw or grub screw. In addition to setting the collar into place, a screw driver can also be used to adjust the grip on the collar. This type of shaft collar is often used in manufacturing applications.
Clamp-type collars are another type of shaft collars. These types allow the shaft to rotate and are used for mounting sensors and fixtures. These collars can be found in one-piece or two-piece styles. They can also be used in harsh environments.
Shaft Collar

Single split shaft collars

Single split shaft collars are used in many applications to protect the shaft from wear and tear. They are easy to install and disassemble, reducing downtime and labor costs. These collars utilize full seating torque of the set screws to apply equal force distribution around the shaft’s circumference, providing stronger holding power.
These shaft collars are available in a variety of materials. They are typically made from different types of steel, including stainless, alloyed steel, nylon, and aluminum. Some are even available in custom sizes. In addition to standard sizes, single split shaft collars also come in a variety of finishes, including black oxide and chrome.
Single split shaft collars come in metric and imperial sizes. They can be made of various materials, including zinc and lead-free steel. These collars are available with a black oxide finish for extra corrosion resistance. They are also available in 303 and 316 stainless steel. They can also be made from engineered plastics.
Single split shaft collars are the most popular style of shaft collars. They are easy to install and disassemble. They provide a tight fit and superior holding power over solid shaft collars. They are also easier to replace and can be used on a variety of shafts. In addition, single split shaft collars are easy to remove and adjust.
Single split shaft collars are available in a variety of bore sizes. They can fit shaft diameters from 1/8″ to four fifteen/16″. Ideally, the material used should be softer than the set screw. You can also choose between non-plated and chrome-plated collars. These collars are available in metric or imperial measurements.
Single split shaft collars are one-piece or two-piece designs. Single-piece shaft collars feature one screw and two-piece collars have two. They are easier to install than single-piece shaft collars and are suitable for lighter duty applications. Single split shaft collars are available in a variety of threaded bore sizes.
Single split shaft collars have a wide range of uses in industrial settings. They can secure bearings on shafts or locate components in motor assemblies. They can also function as mechanical stops. RS PRO offers a wide selection of shaft collars that meet and exceed industry standards.
China OEM CZPT Casing Oscillator for Core Rotary Drilling Rig   shaft collar with set screwChina OEM CZPT Casing Oscillator for Core Rotary Drilling Rig   shaft collar with set screw
editor by CX 2023-11-23